-
The Advantages Of Flat Blister Packaging Machine Selection | Richpacking020.com
Sep 04 , 2021
The blister forming mold and the heat-sealing mold adopted by the flat plate type aluminum plastic blister packer machine are both flat-shaped. And the entire blistering process includes the preheating→the intermittent blow molding→the intermittent filling→the intermittent plate heat sealing→the intermittent typing and embossing→the Intermittent blanking. The blister packaging ...
Read More
-
Introduction Of Flat Blister Packaging Machine | Richpacking020.com
Sep 10 , 2021
The DPP series flat-plate aluminum-plastic/aluminum-aluminum high-speed automatic blister packaging machine is based on the needs of complex customers, and integrates the advantages of international aluminum-aluminum and aluminum-plastic blister packing machines to implement innovative design, development, trial production and improvement. New product. Several models of DPP series 160 and 260 have...
Read More
-
Part One Of The Operation Of The Blister Packaging Machine | Richpacking020.com
Sep 10 , 2021
This Article Will Bring The Installation Of Pvc Rigid Sheet And Aluminum Foil Roll Of Blister Packaging Machine For Rich Packing Customers: Remove The Compression Nut And Stop Sleeve On The Film Reel, Put The Pvc Hard Film Or Aluminum Foil Roll On The Adjustment Sleeve, Install The Stop Sleeve And The Compression Nut And Tighten The Compression Nut To Make The Film Roll On The Adjustment Sleeve It...
Read More
-
Part Two Of The Operation Of The Blister Packaging Machine
Sep 10 , 2021
Aim At The Gap Between The Two Plates, Press The Upper Pressure Roller, And Pull Out The Foam Tape For About Two Meters. When The Upper And Lower Molds Of Blister Packing Machine Are Separated, Press The Stop Button To Stop; Use A Steel Ruler To Measure, The Length Of The Foam Tape After The Molding In Blistering Machine Is Similar To Or Minus 1Mm About The Circumference Of The Feed Roller, And Th...
Read More
-
The Visual Inspection Of Blister Packing Machine
Sep 10 , 2021
At present, there are three main methods for packaging medicines in the world: bottled, bagged, and aluminum-plastic blister packaging. Among them, the way of packaging tablets by blister packaging machines occupies a large share of pharmaceutical packaging. Because in the production and packaging process of tablets, it is necessary to go through the flow of work such as stirring, administering, s...
Read More
-
The Die Structure Of The Tablet Press
Sep 24 , 2021
The die is a tablet press die that suppresses the tablet. The task end faces of the upper and lower punches constitute the appearance of the tablet, and the aperture of the middle die is the diameter of the tablet. The punch die is the primary mission element of the tablet press RQ-ZP. Most of pairs of punching dies contain the three parts: as the upper punch, middle die, and these lower punch. Th...
Read More
-
The Structure Of The Forced Feeder Of The Tablet Press
Sep 24 , 2021
Many pharmaceutical and health care products in the production of solid tablets, is often encountered in the production of tablets, tablet weight, tablet thickness, hardness is not consistent, the down feeder clogging and other problems often need to stop the machine for maintenance resulting in low production efficiency as well as product quality can not be guaranteed. Most of these problems are ...
Read More
-
Capsule Filling Production Equipment
Sep 24 , 2021
In the capsule filling production process of preparing capsules, the filling of drugs is the most important step. 1 Disposal of drugs ①Small-dose medicines or fine medicines can be directly broken into fine powder, passed through a No. 6 sieve, and filled after mixing. ②A large dose of medicine can destroy part of it into fine powder, and other medicinal materials are extracted into a thick ointme...
Read More
-
PVC Rigid Sheet For Cold Stamping
Sep 29 , 2021
The three layers of the cold-stamping and forming hard sheet by blister machine, the outer surface supporting strength layer, the aluminum foil barrier layer, and the inner and outer surface heat-sealing layers are bonded with an adhesive to organically combine them. To become a composite material, it is necessary to ensure that the exquisite blow molding force of the cold stamping forming ha...
Read More
IPv6 network supported 
Home
Products