-
How To Properly Lubricate And Maintain The Tablet Press
Aug 04 , 2022
How to properly lubricate and maintain the tablet press requires more attention: (1) The lubrication of the friction surfaces of the moving parts of the rotary tablet press is an important link to ensure the normal operation of the machine and prolong its service life, especially if the main moving parts run dry in the absence of oil, they will be quickly damaged and cannot be used. . (2) Before u...
Read More
-
How To Adjust The Cam Of Blister Packing Machine?
Aug 04 , 2022
What is the installation sequence of the valve cam of the blister packaging machine on the shaft? First, from the inside to the outside, it is the traction and clamping cylinder cam, the back-stop cylinder cam, the forming blowing cam and the forming cylinder cam. When the return position of the heat sealing cam linkage heat sealing mold is very low, the valve cam is installed according to the pos...
Read More
-
How To Use The Vacuum Pump Of The Blister Packaging Machine Correctly?
Aug 04 , 2022
What are the steps to correctly use the vacuum pump of the blister packaging machine? Start: After the oil level is determined, the vacuum pump can be started. Before starting the vacuum pump, the rotation direction must be checked after one start and every change of wiring. Operation: Before the blister packaging machine works normally, the valve of the intake pipe should be closed, and the pump ...
Read More
-
How Has the Technology Of Chinese tablet press Advanced?
Aug 04 , 2022
China's novel tablet presses and tableting technologies emerge one after another under the increasingly updated technical support. 1. The rotary tablet press focuses on increasing the pre-pressure and improving the tableting quality is a common consideration for many tablet press manufacturers when launching new products. At the same time, the main pressure is the same as the pre-compression, whic...
Read More
-
What Are The Feeding Methods Of The Tablet Press?
Aug 12 , 2022
The feeding system of the tablet press can generally be divided into three types: the shoe feeding system of the single punching machine, the moon feeding system of the low speed rotary tablet press, and the forced feeding part of the high speed press. The system of the single tablet press machine is compared with the structural characteristics of the stamping process. The main structure of the sh...
Read More
-
Why Does The Tablet Press Make Abnormal Noises?
Aug 12 , 2022
Why does the tablet press have abnormal noise? Generally, the abnormal noise of the tablet press has the following reasons: 1. When the synchronous pulley of the tablet press is not parallel, it will cause friction or even damage, resulting in abnormal noise. The solution is to adjust the motor so that the synchronous pulley on the main shaft is parallel to the synchronous pulley on the worm shaft...
Read More
-
Application Of Omron In Blister Packaging Machine
Aug 15 , 2022
The difficulty of the blister packaging machine lies in the servo control for forming and blanking, which is mainly reflected in the synchronous traction and control voltage of the two engines, and the other two servo controls should also achieve synchronous motion control time as follows: In this case Omron uses two rotary encoders to detect the light of the rotation angle and eliminate the tract...
Read More
-
What To Prepare Before Operating The Tablet Press
Sep 02 , 2022
After the mold of the tablet press is installed, turn the steering wheel by hand to make the steering wheel turn 2-3 times, and observe the abnormal friction noise of the upper and lower impact rods on each track and each hole. Turn on the main power switch, the power indicator light is on, and the speed is 0. Press the vacuum cleaner start button, the vacuum cleaner running indicator lights up. N...
Read More
-
How To Save The Tablet Press Mold
Sep 02 , 2022
Tablet press machine molds are essential components in pharmaceutical manufacturing, ensuring that tablets are produced with consistent size, shape, and quality. However, because the production process requires a long time of high pressure and high frequency extrusion, the die is often subjected to wear, which leads to a decline in product quality and efficiency. How to extend the service life and...
Read More