-
The Problem Of The Splicing Table Of The Blister Packaging Machine
Oct 28 , 2021
The splicing table of the blister packaging machine is the docking station for PVC. At the same time, the splicing table has two cylinders to control the release and shutdown protection of the PVC. When the clamping cylinder is released, the forming step is pulled; when the clamping cylinder clamps the PVC Then the forming traction reaches the end of the traction; the third function of the splicin...
Read More
-
Working Characteristics Of Blister Packaging Machine
Oct 28 , 2021
Flat-plate blister packaging machine operation process and working method: the molded plastic sheet is heated to a softened and plastic state at the flat-type preheating and disassembly, and is hauled by step-by-step disassembly to the flat-plate molding and disassembly, shortening the air to blow the softened hard plastic sheet (Or stamping and blow molding) into a blister, filling and disassembl...
Read More
-
Application of PLC Control in Blister Packaging Machine
Nov 19 , 2021
The traction part of the capsule blister packaging machine is controlled by PLC. The calculation shows that the working stroke of the cam at the blister forming part and the heat-sealing part is; the stroke movement time is 0.5 seconds, the far rest time is 1.5 seconds, the return movement time is 0.5 seconds, and the near rest The time is 0.5 seconds. When the forming and heat sealing part of the...
Read More
-
Maintenance Items Of Vacuum Pump For Blister Packing Machine
Nov 26 , 2021
Before the blister packaging machine working, the inlet pipe valves should be closed at first, so that the vacuum pump can run for over 15 minutes under the ultimate pressure state. This way can effectively extract the water pump in the gas. The motors should not be stopped and started frequently (the times is less than 6 time in one hour). (Notice: When the vacuum pumps are running normally, the ...
Read More
-
Improve The Precision Of The Finished Product Of The Tablet Press
Nov 26 , 2021
In the pharmaceutical machinery and equipment industry, with the continuous development of science and technology, new equipment continues to emerge, as is the field of tablet presses, which intensifies the competition in the industry, so there are higher requirements for the processing technology and precision of tablet press machine. , Improve the accuracy of the tablet press, you can enhance th...
Read More
-
The Solution To The Powder Leakage Of The Tablet Press
Nov 26 , 2021
The maintenance method of the rotary tablet press machine is specifically: the tablet press machine manufacturer needs to check the machine itself and parts regularly, basically check the turbine, bearing, compressor, crankshaft, upper and lower rail guides, etc., and solve the problem in time to avoid affecting the machine. In normal operation, after each use, you need to clean the remaining powd...
Read More
-
The Development Status Of Foreign Tablet Presses
Nov 26 , 2021
(1) High speed and high output High speed and high output is the goal that tablet press manufacturers have been pursuing for many years. To catch up with foreign countries in terms of speed and output, domestic tablet presses need to make great development in terms of tablet press design innovation, processing technology and automatic control. (2) The confinement of the tablet pressing process and...
Read More
-
The Basic Operation Of Starting The Blister Machine
Dec 08 , 2021
The first is the first installation of the packaging material PVC rigid film and aluminum foil roll of blister packing machine: remove the compression nut and stop sleeve on the film reel, put the PVC rigid film or aluminum foil roll on the adjusting sleeve, install the stop sleeve and press tightly Screw the nut and tighten the nut so that the film cannot be loosened or rotated on the adjusting s...
Read More
-
Material Device Of Blister Packaging Machine
Dec 08 , 2021
Flat-plate aluminum-plastic blister packaging machine aluminum-plastic reel: sentence includes two parts: aluminum foil reel and plastic film reel. The reel is mainly composed of a cylinder, an inner and an outer stator, a brake ring, and an adjusting nut. The two ends of the cylinder are supported on a supporting shaft with rolling bearings, which are the rotating parts of the reel. When the plas...
Read More
IPv6 network supported 
Home
Products