-
Introduction Of Flat Blister Packaging Machine | Richpacking020.com
Sep 10 , 2021
The DPP series flat-plate aluminum-plastic/aluminum-aluminum high-speed automatic blister packaging machine is based on the needs of complex customers, and integrates the advantages of international aluminum-aluminum and aluminum-plastic blister packing machines to implement innovative design, development, trial production and improvement. New product. Several models of DPP series 160 and 260 have...
Read More
-
Part One Of The Operation Of The Blister Packaging Machine | Richpacking020.com
Sep 10 , 2021
This Article Will Bring The Installation Of Pvc Rigid Sheet And Aluminum Foil Roll Of Blister Packaging Machine For Rich Packing Customers: Remove The Compression Nut And Stop Sleeve On The Film Reel, Put The Pvc Hard Film Or Aluminum Foil Roll On The Adjustment Sleeve, Install The Stop Sleeve And The Compression Nut And Tighten The Compression Nut To Make The Film Roll On The Adjustment Sleeve It...
Read More
-
The Die Structure Of The Tablet Press
Sep 24 , 2021
The die is a tablet press die that suppresses the tablet. The task end faces of the upper and lower punches constitute the appearance of the tablet, and the aperture of the middle die is the diameter of the tablet. The punch die is the primary mission element of the tablet press RQ-ZP. Most of pairs of punching dies contain the three parts: as the upper punch, middle die, and these lower punch. Th...
Read More
-
The Structure Of The Forced Feeder Of The Tablet Press
Sep 24 , 2021
Many pharmaceutical and health care products in the production of solid tablets, is often encountered in the production of tablets, tablet weight, tablet thickness, hardness is not consistent, the down feeder clogging and other problems often need to stop the machine for maintenance resulting in low production efficiency as well as product quality can not be guaranteed. Most of these problems are ...
Read More
-
Capsule Filling Production Equipment
Sep 24 , 2021
In the capsule filling production process of preparing capsules, the filling of drugs is the most important step. 1 Disposal of drugs ①Small-dose medicines or fine medicines can be directly broken into fine powder, passed through a No. 6 sieve, and filled after mixing. ②A large dose of medicine can destroy part of it into fine powder, and other medicinal materials are extracted into a thick ointme...
Read More
-
Replacing The Dosing Plate And Filling Rod Of The Capsule Filling Machine
Oct 10 , 2021
1. Loosen The Fastening Screw Of Capsule Filling Machine To Raise The Powder Hopper With Spring Force; 2. Use A Vacuum Cleaner To Remove The Remaining Powder In The Medicine Pool Ring; 3. Use The Handle To Move The Main Engine To Make The Punch Seat At The Highest Position; 4. Loosen And Remove The Cap Nut, Turn The Knob Clockwise To Raise The Pressure Plate And The Filling Holder And Lift It Off;...
Read More
-
The Problem Of The Splicing Table Of The Blister Packaging Machine
Oct 28 , 2021
The splicing table of the blister packaging machine is the docking station for PVC. At the same time, the splicing table has two cylinders to control the release and shutdown protection of the PVC. When the clamping cylinder is released, the forming step is pulled; when the clamping cylinder clamps the PVC Then the forming traction reaches the end of the traction; the third function of the splicin...
Read More
-
Working Characteristics Of Blister Packaging Machine
Oct 28 , 2021
Blister packaging machines are essential in the pharmaceutical, food, and consumer goods industries. They create sealed packages that protect products from contamination, damage, and environmental exposure while ensuring convenience for users. If you’re exploring blister packaging technology, understanding its working characteristics is crucial for optimizing your production process. This ar...
Read More
-
Application of PLC Control in Blister Packaging Machine
Nov 19 , 2021
The traction part of the capsule blister packaging machine is controlled by PLC. The calculation shows that the working stroke of the cam at the blister forming part and the heat-sealing part is; the stroke movement time is 0.5 seconds, the far rest time is 1.5 seconds, the return movement time is 0.5 seconds, and the near rest The time is 0.5 seconds. When the forming and heat sealing part of the...
Read More
IPv6 network supported 
Home
Products