-
The Problem Of The Splicing Table Of The Blister Packaging Machine
Oct 28 , 2021
The splicing table of the blister packaging machine is the docking station for PVC. At the same time, the splicing table has two cylinders to control the release and shutdown protection of the PVC. When the clamping cylinder is released, the forming step is pulled; when the clamping cylinder clamps the PVC Then the forming traction reaches the end of the traction; the third function of the splicin...
Read More
-
Working Characteristics Of Blister Packaging Machine
Oct 28 , 2021
Flat-plate blister packaging machine operation process and working method: the molded plastic sheet is heated to a softened and plastic state at the flat-type preheating and disassembly, and is hauled by step-by-step disassembly to the flat-plate molding and disassembly, shortening the air to blow the softened hard plastic sheet (Or stamping and blow molding) into a blister, filling and disassembl...
Read More
-
Safety Of Blister Packaging
Nov 09 , 2021
An important issue that currently attracts attention in pharmaceutical packaging is how to reduce accidents caused by children's exposure to drugs or misuse of drugs. Statistics show that 30% of child deaths in many countries are caused by mistakenly ingested drugs. There are even a lot of governments even more legislation to control all blister-packaged drugs, because the packaging of such drugs ...
Read More
-
Advantages Of Tropical Aluminum Blister Packaging
Nov 09 , 2021
Compared with the traditional blister packaging of "aluminum-plastic panel + aluminum-plastic sealed bag", the tropical aluminum blister packaging by the roller blister packaging machine has more prominent advantages. 1. Barrier performance The traditional blister packaging and tropical aluminum blister packaging were tested for water vapor transmission rate, oxygen transmission rate, and pinhole ...
Read More
-
Filling of Blister Packaging Machine
Nov 09 , 2021
The elastic yellow hoses of blister packaging machines are mostly dense-grained hoses wound with stainless steel filaments. The aluminum blister packaging of ten-make capsules is commonly used. The inner diameter of the tube is slightly larger than the outer diameter of the capsule, which can ensure that only a single row is stored in the tube. capsule. Care should be taken to ensure that the hose...
Read More
-
Application of PLC Control in Blister Packaging Machine
Nov 19 , 2021
The traction part of the capsule blister packaging machine is controlled by PLC. The calculation shows that the working stroke of the cam at the blister forming part and the heat-sealing part is; the stroke movement time is 0.5 seconds, the far rest time is 1.5 seconds, the return movement time is 0.5 seconds, and the near rest The time is 0.5 seconds. When the forming and heat sealing part of the...
Read More
-
Maintenance Items Of Vacuum Pump For Blister Packing Machine
Nov 26 , 2021
Before the blister packaging machine working, the inlet pipe valves should be closed at first, so that the vacuum pump can run for over 15 minutes under the ultimate pressure state. This way can effectively extract the water pump in the gas. The motors should not be stopped and started frequently (the times is less than 6 time in one hour). (Notice: When the vacuum pumps are running normally, the ...
Read More
-
Structural Principle Of Blister Packaging Machine
Dec 08 , 2021
The current popular flat-plate blister packaging machine structure is composed of a base, a forming mechanism, a feeder, a heat-sealing and creasing mechanism, a punching mechanism, a traction manipulator, and electrical control. The main drive is driven by the cycloidal pin wheel deceleration and electric drive. The sprocket on the output shaft of the reducer drives the main shaft sprocket to run...
Read More
-
The Basic Operation Of Starting The Blister Machine
Dec 08 , 2021
The first is the first installation of the packaging material PVC rigid film and aluminum foil roll of blister packing machine: remove the compression nut and stop sleeve on the film reel, put the PVC rigid film or aluminum foil roll on the adjusting sleeve, install the stop sleeve and press tightly Screw the nut and tighten the nut so that the film cannot be loosened or rotated on the adjusting s...
Read More